MAIN PAGE > PRODUCTS > HT-300 > MATERIAL SAFETY DATA SHEET BACK ONE
HT-300
Solvent Paint Remover
PRODUCT DESCRIPTION

HOW TO USE PRODUCT

CAUTION

EFFECT ON OTHER MATERIALS

OTHER APPLICATIONS

Product Description

HYDROCLEAN'S HT-300 SOLVENT PAINT REMOVER is a versatile solvent base paint remover specially formulated to crack and lift many forms of paint from a variety of surfaces. Some properties of the product are as follows: Biodegradable, non- flammable, mildly alkaline, thixotropic, solvent/surfactant emulsion system. These properties allow the user to renew and refurbish the old surface with a minimum of labor.

HT-300 has been found to be extremely effective in removing coatings that have a concentration of lead pigment. When used on wood substrates, it will strip multi-layers of paint and leave the wood surface clean of any residual paint coating. Unlike alkaline removers HT-300 will not raise the grain of wood.

Before the application of new paint on wood surfaces, the stripped surface should be cleaned and neutralized with HYDROCLEAN'S HT-540 CLEANING SOLVENT.

How To Use Product

Apply full strength with a brush or roller. Coverage is approximately 50 square feet per gallon. Let stand a minimum of 20 minutes.

IMPORTANT Let stand, do not agitate, rub or work in the product for this will disrupt the chemistry of the preparation. To increase the reaction of the remover, more HT-300 can be applied over the top of the existing paint remover. Use care to apply heavily and evenly. Do not agitate as this may disrupt the chemistry of the original coat of HT-300.

To remove hand scrape or flush with high pressure water. Due to the neutralization effect of water, it may be necessary to let the surface dry before repeating the aforementioned procedure.

To determine both the safety to the base material and the activity toward the unwanted coating, it is recommended that a small patch test be performed. For coatings not successfully removed with HT-300, see data sheets for HYDROCLEAN'S HT-350 EPOXY AND URETHANE PAINT REMOVER and HYDROCLEAN'S HT-716 HEAVY DUTY PAINT REMOVER.

If using HT-300 to remove graffiti, an appropriate cleaner for the particular substrate may be necessary as a follow up to prevent "ghosting".

Caution

As the product contains methylene chloride, use only in a well ventilated area. Harmful if swallowed, in case of skin or eye contact, flush with copious amounts of water immediately. Open container slowly to release possible pressure build up. Keep from freezing. Keep out of reach of children. Methylene chloride has been classified as a hazardous substance. Check Federal E.P.A. and Local regulations on disposal requirements.

DANGER!!! HT-300 contains methylene chloride, which is a substance suspected to be a cancer causing agent in humans.

Effect On Other Materials

Protect any adjacent areas, HYDROCLEAN'S HT-300 SOLVENT PAINT REMOVER will react with most types of paint. Because of the solvency of the product, it may harm asphalt roofs and driveways. Use caution and keep any adjacent asphalt areas wet while applying this product.

Other Applications

HYDROCLEAN'S HT-300 SOLVENT PAINT REMOVER may also be used for tar removal and for the removal of certain exterior water repellents.

Since HYDROCHEMICAL TECHNIQUES shall have no control of the use of the product described herein, HYDROCHEMICAL TECHNIQUES assumes no liability for loss or damage incurred from the improper use of such product.
MAIN PAGE > PRODUCTS > HT-300 : TOP > MATERIAL SAFETY DATA SHEET BACK ONE

http://www.hydroclean.com
All information and photos are copyright Hydroclean.
No material may be reproduced without express written permission from Hydrochemcial Techniques, Inc.

HYDROCLEAN
Hydrochemical Techniques, Inc.
PO Box 2078
Hartford, CT 06145
Tel: 800-278-7681 • 860-527-6350
Fax: 860-527-4067
info@hydroclean.com